The PowerEdge also provides up to eight internal hard drive bays in its 2U chassis, allowing up to 1. High Performance for Today. Redundant NICs and redundant cooling fans help keep the servers running smoothly.
Setting the Standard for Manageability SAS hard drive carriers and memory options are common across the entire line of PowerEdge 9th Generation servers. For more information about specific features, see "Technical Specifications" on page Warranty information may be included within this document or as a separate document. This document may be found on the CDs that came with your system, or on support. This service may not be offered in all locations.
Once you have read the "Safety Instructions" located in the rack installation documentation for your system, install the rails and the system in the rack. See your rack installation documentation for instructions on installing your system in a rack.
The connectors on the back of your system have icons indicating which cable to plug into each connector. Be sure to tighten the screws if any on the monitor's cable connector.
Instead, connect the monitor cable to the connector on the expansion card. Plug the other end of the cable into a grounded electrical outlet or a separate power source such as an uninterrupted power supply UPS or a power distribution unit PDU. Attach the power cord retention bracket on the right bend of the power supply handle.
Repeat the procedure for the second power supply. Plug the other end of the power cables into a grounded electrical outlet or a separate power source such as an uninterrupted power supply UPS or a power distribution unit PDU.
Press the power button on the system and the monitor. The power indicators should light. Adjust the monitor's controls until the displayed image is satisfactory. If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the Quick Installation Guide.
Be sure the operating system is installed before installing hardware or software not purchased with the system. NOTE: For additional information about environmental measurements for specific system configurations, see www.
Voir le site support. Pour plus d'informations, consultez le site www. Ce service n'est disponible que dans certains pays. Les voyants d'alimentation doivent s'allumer. Welcome to ManualMachine.
We have sent a verification link to to complete your registration. The system prompts you to enter and verify the password. If a character is illegal for password use, the system beeps. NOTE: The setup password can be the same as the system password. If the two passwords are different, the setup password can be used as an alternate system password.
However, the system password cannot be used in place of the setup password. After you verify the password, the Setup Password setting changes to Enabled. The next time you enter the System Setup program, the system prompts you for the setup password. A change to the Setup Password option becomes effective immediately restarting the system is not required. If Setup Password is set to Enabled, you must enter the correct setup password before you can modify most of the System Setup options.
When you start the System Setup program, the program prompts you to enter a password. If you do not enter the correct password in three attempts, the system lets you view, but not modify, the System Setup screens—with the following exception: If System Password is not set to Enabled and is not locked through the Password Status option, you can assign a system password however, you cannot disable or change an existing system password.
BMC provides the following features:. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. Model EMS Contents 1 About Your System. About Your System This section describes the physical, firmware, and software interface features that provide and ensure the essential functioning of your system.
About Your System Accessing System Features During Startup Table describes keystrokes that may be entered during startup to access system features. Table For more information, see the documentation for your RAID card. Front-Panel Features and Indicators Figure shows the controls, indicators, and connectors located behind the optional rack bezel on the system's front panel. Figure Front-Panel Features and Indicators 1 2 3 4 5 6 7 8 0 2 4 1 3 5 Table The power button controls the DC power supply output to the system.
NOTE: If you turn off the system using the power button and the system is running an ACPI-compliant operating system, the system performs a graceful shutdown before the power is turned off. If the system is not running an ACPI-compliant operating system, the power is turned off immediately after the power button is pressed.
This button can be pressed using the end of a paper clip. Use this button only if directed to do so by qualified support personnel or by the operating system's documentation. The LCD lights during normal system operation.
Both the systems management software and the identification buttons located on the front and back of the system can cause the LCD to flash blue to identify a particular system. The LCD lights amber when the system needs attention, and the LCD panel displays an error code followed by descriptive text. Hard-Drive Indicator Codes The hard-drive carriers have two indicators—the drive-activity indicator and the drive-status indicator.
Hard-Drive Indicators 1 2 1 drive-status indicator green 2 green drive-activity indicator and amber. Drive failed Blinks amber four times per second. Drive rebuilding Blinks green slowly. Drive online Steady green. Rebuild aborted Blinks green three seconds, amber three seconds, and off six seconds. Back-Panel Features and Indicators Figure shows the controls, indicators, and connectors located on the system's back panel. Back-Panel Features and Indicators 1 2 3 4 13 12 11 10 9 8 7 6 5.
Power Indicator Codes The power button on the front panel controls the power input to the system's power supplies. Power supply fault Amber indicates a problem with the power supply. AC line status Green indicates that a valid AC source is connected to the power supply. NIC Indicators 1 2 1 link indicator 2 activity indicator Table Link indicator is green The NIC is connected to a valid link partner on the network.
Activity indicator is amber blinking Network data is being sent or received. LCD Status Messages The system's control panel LCD provides status messages to signify when the system is operating correctly or when the system needs attention. Setup program. Setup Program" on page Cooling Problems" on page Battery" on page Another fan failure additional scrolling messages. See will put the system at risk of over- "Troubleshooting System Cooling heating.
Problems" on page Update Tech Sheet located on support. If problem persists, see "Getting Help" on page If the problem persists, ensure that the microprocessor heat sinks are properly installed. See "Troubleshooting the Microprocessors" on page If acceptable range. If the last Supplies" on page Reinstall the expansion-card cage.
See "Getting Help" on page If the problem persists, the riser card or system board is faulty. Slot function. Drive" on page If the problem persists, see your RAID documentation. E No Memory No memory is installed in the Install memory. See "Installing system. Memory Modules" on page Error detected Memory" on page Memory subsystem Memory" on page Memory" on page E Timer Fail Timer refresh failure. E Parity Error Parity error. EB Kybd Controller Keyboard controller failure. SMI initialization failure.
Ensure that DRAC cables and connectors are properly seated. If problem persists, see your DRAC documentation.
Check screen for specific error messages. E Memory Incorrect memory configuration. Check screen for specific error Population Memory population order messages. See "Troubleshooting incorrect. System Memory" on page If no memory card is present, the "Crd " string is left out of the message. If no memory riser card is present, the "Crd " string is left out of the message. I Intrusion System cover has been removed.
Information only. Check the SEL for details on the A maximum of three error events. The fourth message displays as the standard overflow message. Removing LCD Status Messages For faults associated with sensors, such as temperature, voltage, fans, and so on, the LCD message is automatically removed when that sensor returns to a normal state.
System Messages System messages appear on the screen to notify you of a possible problem with the system. Redundant memory Installed memory modules are not the Ensure that all memory modules are of disabled!
Memory same type and size; faulty memory the same type and size and that they are configuration does not module s. If the problem support redundant memory. Attempting to update Remote Configuration request has Wait until the process is complete. Remote Configuration. Please wait Retry the BIOS update. If problem Failed! See is installed on system CMOS has been cleared. Figure for jumper location. CPUs with different cache Microprocessors with different cache Ensure that all microprocessors have the sizes detected!
Decreasing available Faulty or improperly installed memory See "Troubleshooting System Memory" memory modules. DIMM pairs must be matched Mismatched or unmatched DIMMs Ensure that all pairs of memory modules in size, speed, and installed; faulty or improperly seated are of the same type and size and that technology.
The following memory module s. DIMMs beginning with slot 1. See "System with slot 1. The following must be populated in sequential order, Memory" on page DIMM is electrically beginning with slot 1. Diskette drive n seek Incorrect configuration settings in the failure System Setup program. Faulty or improperly installed diskette drive.
Loose tape drive interface cable, or loose power cable. Diskette read failure Faulty or improperly inserted diskette or tape drive.
See "Troubleshooting a Diskette Drive" on page Diskette subsystem reset Faulty or improperly installed diskette failed or tape drive. Drive not ready Diskette missing from or improperly inserted in diskette drive. DIMMs must installed; faulty or improperly seated are of the same type and size and that be installed in pairs of memory module s.
See "System matched memory size, Memory" on page If the problem speed, and technology. Faulty or improperly seated memory See "Troubleshooting System Memory" module s. FBD training error: The following branch has been disabled: Branch x. General failure The operating system is unable to carry out the command. Reboot to take the system out of detected manufacturing mode.
No timer tick interrupt Faulty system board. Use a bootable diskette. If the problem persists, see "Getting Help" on page Ensure checksum failure is detected during that all appropriate cables are securely shadowing. If Loose cables to expansion card s ; the problem persists, see "Troubleshooting Expansion Cards" on faulty or improperly installed page See Figure for jumper location. If the problem persists, see "Troubleshooting Expansion Cards" on page Read fault Requested sector not found.
Ensure faulty. Sector not found Faulty diskette or hard drive. Shutdown failure Shutdown test failure. The amount of system Memory has been added or removed memory has changed or a memory module may be faulty. Time-of-day clock stopped Faulty battery or faulty chip. See "Troubleshooting the System Battery" on page Dell recommends purchasing DIMM y memory upgrade kits directly from www.
Unsupported CPU Microprocessor s is not supported by combination the system. Unsupported CPU stepping detected. See the CDs that came with on the boot hard drive. No micro code Micro code update failed. Update the BIOS firmware. See "Getting update loaded for Help" on page Warning Messages A warning message alerts you to a possible problem and prompts you to respond before the system continues a task.
Diagnostics Messages When you run system diagnostics, an error message may result. Alert Messages Systems management software generates alert messages for your system. Using the System Setup Program After you set up your system, run the System Setup program to familiarize yourself with your system configuration and optional settings.
Responding to Error Messages You can enter the System Setup program by responding to certain error messages. Using the System Setup Program Using the System Setup Program Table lists the keys that you use to view or change information on the System Setup program screens and to exit the program.
In many fields, right arrows you can also type the appropriate value. Main System Setup Program Screen Table lists the options and descriptions for the information fields that appear on the main System Setup program screen. System Date Resets the date on the system's internal calendar. Memory Information Displays information related to installed system, video, and redundant memory, including size, type, and speed. CPU Information Displays information related to microprocessors speed, cache size, and so on.
Enable or disable Hyper-Threading technology by changing the setting of the Logical Processor option. System Setup Program Options continued Option Description Boot Sequence Determines the order in which the system searches for boot devices during system startup. Available options can include the diskette drive, CD drive, hard drives, and network. Hard disk allows the USB Auto default flash drive to act as a hard drive.
Floppy allows the USB flash drive to act as a removal diskette drive. Integrated Devices See Table Serial Communication Displays a screen to configure serial communication, external serial connector, fail- safe baud rate, remote terminal type, and redirection after boot. System Security Displays a screen to configure the system password and setup password features. Keyboard NumLock Determines whether your system starts up with the NumLock mode activated on On default or key keyboards does not apply to key keyboards.
Select Report for Report default host systems that have keyboards attached. This setting does not affect the operation of the keyboard itself if a keyboard is attached to the system. Asset Tag Displays the customer-programmable asset tag number for the system if an asset tag number has been assigned. Logical Processor Displays when the processors support HyperThreading.
Enabled Enabled default permits all logical processors to be used by the operating system. Only the first logical processor of each processor installed in the system is used by the operating system if Disabled is selected. Adjacent Cache Line Enables or disables optimal use of sequential memory access. Prefetch Disable this option for applications that require high use of random Enabled default memory access.
Virtualization Technology Displays when the processor s support Virtualization Technology. Disabled default Enabled permits virtualization software to utilize Virtualization Technology functions incorporated in the processor design. This feature can only be used by software that supports Virtualization Technology. Hardware Prefetcher Enables or disables the hardware prefetcher.
Enabled default Demand-Based Power Enables or disables demand-based power management. If any of the CPUs do not support demand-based power management, the field will become read-only, and automatically set to Disabled. Processor X ID Displays the family and model number of each processor. A submenu displays processor core speed, amount of level 2 cache, and number of cores.
Integrated Devices Screen Table lists the options and descriptions for the information fields that appear on the Integrated Devices screen. PXE support allows the system to boot default from the network. Changes take effect after the system reboots. This field does not have user-selectable settings. Diskette Controller Enables or disables the system's diskette drive controller. When Auto is selected, Auto default the system turns off the controller when necessary to accommodate a controller card installed in an expansion slot.
You can also configure the drive as Read-Only , or Off. When using the Read-Only setting, the drive cannot be used to write to a disk. Serial Communication Screen Table lists the options and descriptions for the information fields that appear on the Serial Communication screen.
Off default Failsafe Baud Rate Displays the failsafe baud rate used for console redirection when default the baud rate cannot be negotiated automatically with the remote terminal. This rate should not be adjusted. System Security Screen Table lists the options and descriptions for the information fields that appear on the System Security screen.
System Security Screen Options Option Description System Password Displays the current status of your system's password security feature and allows you to assign and verify a new system password. NOTE: See "Using the System Password" on page 45 for instructions on assigning a system password and using or changing an existing system password.
Setup Password Restricts access to the System Setup program in the same way that you restrict access to your system using the system password feature. NOTE: See "Using the Setup Password" on page 47 for instructions on assigning a setup password and using or changing an existing setup password.
To lock the system password, assign a setup password in the Setup Password option and then change the Password Status option to Locked. To unlock the system password, enter the setup password in the Setup Password field and then change the Password Status option to Unlocked. Power Button Turns system's power off and on.
0コメント